Belt Finder

Radius Friction Top Mold to Width with Load-Sharing™ Edge

Series 2400
Request a Quote

Secure products on low-level inclines and declines with the Intralox Series 2400 Mold to Width Radius Friction Top with Load-Sharing Edge belt.

Part of the industry’s most dependable radius series, this belt has a Friction Top surface that stabilizes products during gradual elevation shifts. Its Load-Sharing edge distributes stress to minimize fatigue failures, while its 42% open area simplifies cleaning.

  • Load-Sharing edge extends belt life
  • Available in the following widths:
    • 4 in (101.6 mm)
    • 6 in (152.4 mm)
    • 8 in (203.2 mm)
    • 10 in (254 mm)
inmm
Pitch1.0025.4
Minimum Width4.0101.6
Opening Size (approximate)0.35 x 0.308.9 x 7.6
Open Area42%
Hinge StyleOpen
Rod Retention; Rod TypeSnap-lock; headed

  • Contact Intralox for precise belt measurements and stock status before designing equipment or ordering a belt.
  • Flush edge design features an extension to reduce the opening size.
  • Load-Sharing™ belt edge improves how the load is shared and minimizes belt fatigue failure.
  • Available in grey polypropylene with grey rubber and white polypropylene with white rubber.
  • Each belt material has a default rod material. Other rod materials are available. Intralox can help identify the best belt and rod material combination for your application.
  • Detailed material information is provided in Product Line.
  • Designed for sideflexing applications with a standard turn ratio of 2.2 times the belt width.
  • Minimum recommended turn ratio is 1.95. Contact Intralox Customer Service when considering minimum turn ratio.
  • Temperature, environmental conditions, and product characteristics affect the maximum degree of incline. Consider these factors when designing conveyor systems using these belts.
  • Available with hold down guides
  • Radius belt wearstrips are available.
  • Available widths: 4 in (101.6 mm), 6 in (152.4 mm), 8 in (203.2 mm), and 10 in (254 mm).
  • Indent for friction surface:
    • On 4-in (101.6 mm) and 6-in (152.4 mm) widths: indent molded at 0.70 in (17.78 mm).
    • On 8-in (203.2 mm) and 10-in (254 mm) widths: indent molded at 0.95 in (24.1 mm).
  • For 4 in (102 mm) wide belts with hold down guides, do not use glass-filled nylon split sprockets.
  • Maximum number of sprockets:
    • 4 in (101.6 mm) belts without hold down guides: two sprockets.
    • 4 in (101.6 mm) belts with hold down guides: one sprocket.
    • 6 in (152.4 mm) belts without hold down guides: four sprockets.
    • 6 in (152.4 mm) belts with hold down guides: three sprockets.
    • 8 in (203.2 mm) belts with and without hold down guides: five sprockets.
    • 10 in (254 mm) belts with and without hold down guides: seven sprockets.
  • Minimum nosebar diameter:
    • belts without hold down guides: 1.375 in (34.9 mm).
    • belts with hold down guides: 1.50 in (38.1 mm).

Base Belt MaterialDefault Rod Material, Diameter 0.18 in (4.6 mm)Hold Down GuidesStraight Belt Strength lbf (N)Curved Belt StrengthTemp. Range (continuous)Belt Mass lb/ft (kg/m)
4.0 in (101.6 mm)6.0 in (152.4 mm)8.0 in (203.2 mm)10.0 in (254 mm)F°C°4.0 in (101.6 mm)6.0 in (152.4 mm)8.0 in (203.2 mm)10.0 in (254 mm)
PolypropyleneNylonWithout 400 (1,780)600 (2,670)800 (3,560)1,000 (4,450)For curved belt strength calculations, contact Intralox Customer Service.34 to 1501 to 660.48 (0.72)0.73 (1.08)0.97 (1.44)1.21 (1.79)
With 242 (1,080)600 (2,670)800 (3,560)1,000 (4,450)34 to 1501 to 660.51 (0.76)0.77 (1.14)1.02 (1.52)1.28 (1.89)

Series 2400