| in | mm | |
| Pitch | 1.50 | 38.1 |
| Minimum Width | 5 | 127 |
| Width Increments | 1.00 | 25.4 |
| Opening Size (approximate) | 0.50 × 0.75 | 12.7 × 19.7 |
| Open Area | 50% | |
| Hinge Style | Open | |
| Rod Retention; Rod Type | Occluded edge; unheaded | |
- This belt has pinch points. See the Safety section in the Intralox Conveyor Belting Installation, Maintenance & Troubleshooting Manual for more information.
- Contact Intralox for precise belt measurements and stock status before designing equipment or ordering a belt.
- Flush edge or tab edge available.
- Belt openings pass straight through the belt to simplify cleaning.
- Available in grey polypropylene with grey rubber, white polypropylene with white rubber, and natural polyethylene, with white rubber.
- Each belt material has a default rod material. Other rod materials are available. Intralox can help identify the best belt and rod material combination for your application.
- Detailed material information is provided in Product Line.
- Non-sliding drive system provides reduced belt and sprocket wear, and low back-tension.
- Designed for radius applications with a minimum turn radius of 2.2 times the belt width (measured from the inside edge).
- Temperature, environmental conditions, and product characteristics affect the maximum degree of incline. Consider these factors when designing conveyor systems using these belts.
- If a standard edge or tabbed edge wearstrip is used to hold the belt in place, do not retain sprockets on the shaft. In this case, the wearstrip maintains the lateral belt position.
- Tab edge belt width measurement does not include tabs. (Tabs extend approximately 0.5 in (13 mm) × 0.25 in (6 mm) on each side of belt, inside the wearstrip.)
- Molded indent: 1.75 in (44 .5 mm).
- Maximum belt width in turns: 36 in (914 mm).
| Base Belt Material | Base/Friction Top | Default Rod Material, Diameter 0.24 in (6.1 mm) | Belt Strength | Curved Belt Strength | Temp. Range (continuous) | Belt Mass | Friction Top Hardness | Agency Acceptability | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| lbf/ft | N/m | °F | °C | lb/ft² | kg/m² | FDA (USA) | EU MC1 | ||||||
| Polypropylene | Grey/grey | Acetal | 1,600 | 23,400 | For curved belt strength calculations, contact Intralox Customer Service. | 34 to 150 | 1 to 66 | 2.20 | 10.74 | 64 Shore A | |||
| Polypropylene | White/white | Acetal | 1,600 | 23,400 | 34 to 150 | 1 to 66 | 2.20 | 10.74 | 55 Shore A | 2 | 3 | ||
| Polyethylene | Natural/white | Acetal | 1,000 | 14,600 | -50 to 120 | -46 to 49 | 2.30 | 11.23 | 55 Shore A | 2 | 3 | ||
| Polypropylene | Grey/grey | Polypropylene | 1,400 | 20,400 | 34 to 150 | 1 to 66 | 2.12 | 10.35 | 64 Shore A | ||||
| Polypropylene | White/white | Polypropylene | 1,400 | 20,400 | 34 to 150 | 1 to 66 | 2.12 | 10.35 | 55 Shore A | 2 | 3 | ||
European Migration Certificate providing approval for food contact according to EU Regulation 10/2011.
FDA compliant with restriction: Do not use in direct contact with fatty foods.
EU compliant with restriction: Do not use in direct contact with fatty foods.
| Document Name | Document Type | File Type | File Size |
|---|---|---|---|
| S2200_FrictionTop_FlushEdge_[TopView]_(Imperial).dxf | CAD Drawing | DXF | 425 KB |
| S2200_FrictionTop_FlushEdge_[TopView]_(Metric).dxf | CAD Drawing | DXF | 433 KB |
| S2200_FrictionTop_TabbedEdge_[TopView]_(Imperial).dxf | CAD Drawing | DXF | 503 KB |
| S2200_FrictionTop_TabbedEdge_[TopView]_(Metric).dxf | CAD Drawing | DXF | 514 KB |
